cat 302.5

2024-11-22T12:49:59 | By john deere 333g skid steer specs , DOD blog

cat 302.5 I have a 2003 cat 302.5 ran fine 6 months ago. Went out to start it and it will only idle, no throttle response. I let it sit and idle for over a hour, thinking maybe if it ran for a while it might start operating properly, with no luck. I have plenty of . Review: 2015 Hyundai Robex R55-9 Excavator. Advisor February 7, 2016. Playing ball with the big guys in construction, the Hyundai Robex R55-9 is punching well above its weight. Considering its ample competition in well .

0 · caterpillar 302.5 for sale
1 · cat 302.5 wiring diagram
2 · cat 302.5 specs
3 · cat 302.5 problems
4 · cat 302.5 parts diagram
5 · cat 302.5 hydraulic oil
6 · cat 302.5 for sale
7 · 302.5 cat excavators for sale

Browse a wide selection of new and used SANY SY26U Mini (up to 12,000 lbs) Excavators for sale near you at MachineryTrader.com

Browse a wide selection of new and used CATERPILLAR 302.5 Excavators for .

The Cat 302 CR is a compact and powerful mini excavator with a tilt up cab, stick steer option, . I have a Cat 302.5 mini digger, All seems to be working fine apart from having no real downward pressure. If i extend the boom our a little, sit the bucket on the floor i'm unable to lift the digger but everything else seems fine, at least i haven't noticed any other issues. Hi guys, I just picked up a Cat 302.5 and it has some issues I need to sort out. Anybody know where I can find used parts on the west coast. I need some body parts, a new dozer blade for it, and a few other odds and ends. Also, the engine wont idle down. It will idle fine until I rev it up, but it will not come back down.

I have a 2003 cat 302.5 ran fine 6 months ago. Went out to start it and it will only idle, no throttle response. I let it sit and idle for over a hour, thinking maybe if it ran for a while it might start operating properly, with no luck. I have plenty of . I have a mini excavator 302.5 that had hydrolic hose busted on. I replaced 2 hoses and tested it to make sure that was the only hoses busted. After i replaced them i started it up to test it and everything worked fine, However Another employee took the entire seat out and disassembled the lower. I have a 2001 CAT 302.5, 3000 hrs, worked good in the fall, this spring i fired it up and no hydraulics at all. Fluid is good, filters are good, hydraulic disconnect solenoid is engaging, I pulled it off to confirm the action, check all electrical to make sure. It doesn't seem to be a electrical issue. Hello, first post here but I've been following along for a while. Very helpful forum! I recently installed a hydraulic thumb on our 2000 Cat 302.5 (4AZ01260) and have been reluctant to use it yet because I think we need to incorporate .

I have a CAT 302.5 with a 3013 engine, Prefix: 4AZ04565. The machine runs excellent for about 20 min then it will smoke a little blue/white, lose power, and run rough. The smoke smells like fuel. If I prime it a few times it will smooth out so I'm thinking it is a fuel starvation issue. Having hydraulic issues with a cat 302.5. The boom will not lift while the bucket is curling. (They only work together at an extremely slow pace.) Also it tracks to the right. Switched lines from one track to other and right was still slower. Figured problem must be in final drive. The machine is a Cat 302.5. everything works on it fine, but the arm will only pivot in one direction with the foot pedal control. It will gradually come back over hours of use but never past a certain point to the other direction. As soon as you press the pedal to the other side, it goes back perfect with plenty of power and speed.

I have run similar sized machines that my friends own that were not Cat machines. One was a Kubota that was around 6000 lb. While a nice machine, the 303.5 is in what I consider to be a different class even though they are both mini Ex's. The Cat is substantially heavier built, and has many wonderful features such as the new COMPASS control system. I have a Cat 302.5 mini digger, All seems to be working fine apart from having no real downward pressure. If i extend the boom our a little, sit the bucket on the floor i'm unable to lift the digger but everything else seems fine, at least i haven't noticed any other issues. Hi guys, I just picked up a Cat 302.5 and it has some issues I need to sort out. Anybody know where I can find used parts on the west coast. I need some body parts, a new dozer blade for it, and a few other odds and ends. Also, the engine wont idle down. It will idle fine until I rev it up, but it will not come back down. I have a 2003 cat 302.5 ran fine 6 months ago. Went out to start it and it will only idle, no throttle response. I let it sit and idle for over a hour, thinking maybe if it ran for a while it might start operating properly, with no luck. I have plenty of .

I have a mini excavator 302.5 that had hydrolic hose busted on. I replaced 2 hoses and tested it to make sure that was the only hoses busted. After i replaced them i started it up to test it and everything worked fine, However Another employee took the entire seat out and disassembled the lower.

I have a 2001 CAT 302.5, 3000 hrs, worked good in the fall, this spring i fired it up and no hydraulics at all. Fluid is good, filters are good, hydraulic disconnect solenoid is engaging, I pulled it off to confirm the action, check all electrical to make sure. It doesn't seem to be a electrical issue. Hello, first post here but I've been following along for a while. Very helpful forum! I recently installed a hydraulic thumb on our 2000 Cat 302.5 (4AZ01260) and have been reluctant to use it yet because I think we need to incorporate . I have a CAT 302.5 with a 3013 engine, Prefix: 4AZ04565. The machine runs excellent for about 20 min then it will smoke a little blue/white, lose power, and run rough. The smoke smells like fuel. If I prime it a few times it will smooth out so I'm thinking it is a fuel starvation issue.

caterpillar 302.5 for sale

Having hydraulic issues with a cat 302.5. The boom will not lift while the bucket is curling. (They only work together at an extremely slow pace.) Also it tracks to the right. Switched lines from one track to other and right was still slower. Figured problem must be in final drive. The machine is a Cat 302.5. everything works on it fine, but the arm will only pivot in one direction with the foot pedal control. It will gradually come back over hours of use but never past a certain point to the other direction. As soon as you press the pedal to the other side, it goes back perfect with plenty of power and speed.